News

This is a translation of the bulk of Bodo Wiegand’s latest newsletter, about Lean in Germany, followed by my comments:

At the beginning of  this year I was at a company with a high level of Lean in Manufacturing and went into a discussion with the Board about how to go further the realize the full potential .

They did not want to get into the administrative areas, since there the world bosses were allowed to have their say — even though there was real potential there . But life in a matrix organization, as has been frequently noted , is very pleasant.  Before doubly protected kingdoms can be torn down, it takes usually a crisis or a new boss. You know my motto: “Give a slave of two masters and he is a free man . ”

Well then, what? We talked about opportunities in Manufacturing and, on our tour of the facilities, spent a bit more time on Maintenance. They were quite proud of the TPM plans they showed me, with a regular preventive maintenance plan, and involvement of production operators in routine maintenance. The whole range of tools set up and implemented was classic. Their pride was a new conveyor system, to which a maintenance technician was dedicated for inspections, routine maintenance, and troubleshooting . It sounded to me like: “With such investments, we must be able to afford this, to avoid the risk of failure .”

In another area , there were identical machines;  in the next hall several different presses. With the exception of heat treatment (3 shifts ) all areas were still working in 2 shifts. Of course, Maintenance is an area where you can see what happens inside just by looking from the outside. But my gut was telling me not to scream “wonderful” about the perfect organization. Instead, alarm bells went off and immediately came the question “What does the value stream look like?”  Proudly, the manager led me to the team leader room.  There hung the map. And I immediately saw  the date on which it was drawn. It was three years ago. Well, I expressed my concern: ” Is the new system taken into account ? ”

“No ”

This is a mistake we encounter often. Value streams change with the actions we perform and should be revised especially after new investments or major changes. Bottlenecks migrate and thereby change the production system. Back in the office, we discussed again his question of why the value stream is important to Maintenance.  I told him about Lean Maintenance. He asked “Should Maintenance be organized according to the value stream? – Why? ”

” In the value stream,” I answered, “bottlenecks are detected, critical facilities are identified from a customer perspective and process stability is visible. Priorities given to equipment are the basis for  maintenance and spare parts stocking strategies.”

That was too high-level for him.

So – I tried again. Equipment that is  the bottleneck or is in close proximity to customers is prioritized because it is important for delivery, and the bottleneck caps the production volume. If the bottleneck stops, so does the whole production system. If the last machine stops, which is important for  delivery, the safety stock increases .

Maintenance and stocks ? – The Board id not understand. ” What does Maintenance have to do with working capital ? ”

“Well, safety stocks are usually based on the worst-case  interruption time for repairs and mostly with people-related impact to it. ” In this case, it was three weeks.

It is usually two to three weeks – no one knows why.

“Can the maintenance strategy reduce working capital? ”

“Sure,” I answered. ” By prioritizing the facilities you identify the ones that are important for delivery . There you focus your maintenance activities and develop your spare part strategy. This is the only place where it is important whether this system fails. Failure analysis identifies the components that may be responsible. Then individual maintenance strategies must be developed for these components .

This starts with wear-dependent important components that are not predictable with sensor monitoring, and goes as far as the maintenance strategy of  “creating redundancy.”  The aim is to increase the process stability and to allow no loss. This reduces the need for safety stock . From that we get a feel for what would be the biggest shutdown and can estimate this time .

The next step is to optimize the maintenance time, ie to reduce the repair times to a minimum . If it is possible to organize the maintenance response to a quasi Formula 1 – standard, and you also develop a maintenance strategy adapted to it , you can make the maintenance times as short as possible. The safety stocks can then be lowered furthe . Gut feel no longer prevails. Instead, you have clear maintenance strategies based on numbers , facts, and figures. ”

” But isn’t that more effort? ”

“Perhaps on the facilities with high priorities. But why do you inspect machines that you take out of production for entire shifts? You have many working only 2 shifts. If a machine fails, it can be replaced by others. And why are you dedicating one person to your new conveyor system , which is certainly not a bottleneck?  Why do you thoroughly inspect your presses and have not considered how the failure of one could be compensated by the use of another. On such equipment “farms,” you do not need preventive maintenance in the classical sense, only a maintenance strategy that is appropriate for this case. ”

It is important to deliver and therefore you need a stable process. For this, you should evaluate the maintenance person, and not by cost. With a Lean Maintenance approach you will go from  failure-driven maintenance to  largely planned and predictable maintenance, requiring  less effort, providing higher process stability and reducing  costs for emergency response .

The result: we have reduced the worst-case repair time from 2.5 days to 8 hours, and safety stocks to two to three days, while reducing the costs of  external maintenance services by 80%.

The necessary investments in the sensors, redundancy or spare parts have been more than covered by the reduction in working capital. The annual reductions amount to a low seven-figure sum . The greatest gain was that the production and the maintenance staff are now working towards a common goal and are understood as a team . It culminated in this statement of the initially reluctant maintenance manager : “We want to be measured by the manufacturing productivity and working capital. “